Click Here To Visit
 


Another iZook Product ReviewKlune-V R.A.D. Valve Stems
with Bill Johnston

Click through for a closer look...When on the street we run our tires at a set air pressure that will allow the best traction while maintaining a safe level of control. When on the trail we maximize the tire footprint by dropping the air pressure. But finding a way to drop that air pressure quickly without disassembling the valve stem (and possibly losing the schrader valve) has been a major concern. The Rapid Air Down Valve Stems by Klune-V are a really high-tech answer to a simple need.

Click through for a closer look...Click through for a closer look...The key to the R.A.D. system is the series of holes drilled at the base of the stem. These bypass the schrader valve for more air flow. Tightening the external knurled nut shuts down these passages using an O-ring incorporated in the base of the nut.
Click through for a closer look...Click through for a closer look...By including two different grommet sizes, you can use it on either of the two standard valve stem hole sizes (29/64" and 5/8"). But not all wheels will work with this system, as we found out. A modular rim with an angled stem outlet like the one on the right would not work. The new stem must be mounted perpendicular to the wheel surface.
Click through for a closer look...Click through for a closer look...The rim on the left would not work either, there is too little clearance between the stem and the wall of the rim. The R.A.D. stem requires a clear seating area of 3/4". The wheel on the right is the style we used for this installation.

Click through for a closer look...Click through for a closer look...Click through for a closer look...Click through for a closer look...

The bead on the tire must be unseated to install a valve stem (they go in from behind) so we headed down to the local Martin Tire store. They were more than helpful and pretty curious about the new equipment. Why didn't we just pull out the tire spoons and do it in the garage? Because we didn't have cool equipment like this sitting around...

Click through for a closer look...     Click through for a closer look...     Click through for a closer look...

When installing the stems, use a rag to catch any dropped parts. Trying to fish out parts inside of the tire is a pain in the rear. There is also a nut included in the kit to take the place of the knurled component when tightening the whole thing down. The instructions call it an 'installation tool', but it's basically a nut.

Click through for a closer look...Click through for a closer look...Click through for a closer look...

Click through for a closer look...Click through for a closer look...Once the stem is torqued down you remove the nut (installation tool). We found that after it was torqued down, it didn't want to come loose. We used the knurled knob as a jam nut underneath so we could hold everything in place to loosed the installation nut up top. There is nothing about this in the instructions, but a little common sense and some quick thinking gave us the answer.
Click through for a closer look...Click through for a closer look...Now place the knurled knob. Don't forget the valve cap, because it works as a lock nut to ensure the external nut doesn't back off while driving.

Finally, you have to balance the tire to keep the vibrations down. These valves weigh 1.75 ounces (a little heavier that most) so don't think you can get away without balancing.

Click through for a closer look...Although these new R.A.D. Valve Stems are wider than normal, they are still very short. They stay tucked in and out of the way of the rocks using the wheels we are running. If you plan to install a set of these on a new set of wheels, try to find a set of wheels that set the valve farther away from the edge of the rim.

We are running a 33/12.50/15R TSL with this configuration. It only took 20 seconds to drop the air pressure from our street level of 28 psi down to 8 psi for the trail.

This is a fastest way to air down, it's even faster than pulling the valve stem.

Manufacturer:

Klune V
7323 Coldwater Canyon Ave.
North Hollywood, CA  91605-4206
800-222-3619
www.klunev.com

Supplier:

Spidertrax
PO Box 340
New Milford, NJ 07646
1-800-286-0898 Orders
1-201-225-0157 Tech & Questions
1-810-821-0263 Fax
www.spidertrax.com

 

With help from:

Martin Tire Company
5255 Woodrow Bean Trans Mountain
El Paso, TX  79924
915-751-0404
www.martintire.com

 

08/11/10 14:46

[accessories/footer.htm]