Click Here To Visit
Click Here To Visit


Wrenchin' with IZook
with Bill Johnston

Hi-Lift Jack Installation

I was looking for more room under the hood the other day and under some desert dirt I found the little scissors jack that Suzuki thoughtfully included with my Samurai. It was then that I realized the stock jack may not be able do it's job since I lifted the Zook. I took out the jack and extended it to it's fullest height - a full 14.25". It came to just about 7 inches below the frame. Time to get a new jack...

I knew I wanted a Hi-Lift, but I was afraid that it wouldn't fit inside the rig. I had heard tales of people actually cutting off a section of the jack to make it fit, but if I was going to spend upwards of $60 for a tool, I wasn't going to take a hacksaw to it any time soon!

The Hi-Lift jack is offered in many sizes (see the table below), so I decided to take some measurements. I found that the width of the rear area was just about 51", so I decided on the 48" all cast model (HL-485). The cast style is more capable.

P/N EJ-550 HL-364 HL-424 HL-425 HL-484 HL-485 HL-604 HL-605
Model EJ 36" 42" 42" 48" 48" 60" 60"
Actual
Height
36" 41" 43.5" 46" 48.75" 50.75" 59.25" 61.75"
Max Lift 21.13" 27" 32" 34" 37.24" 38.63" 49.75" 48.25"
Construction Cast/
Steel
Cast/
Steel
Cast/
Steel
Cast Cast/
Steel
Cast Cast/
Steel
Cast
Full shot of mounted jack.Next I had to find a good location inside, safe from the elements and safe from anyone else looking for a tall jack! Finding a mounting location isn't very hard. Finding one that is out of the way, yet accessible and easy to hide was quite another.
2.5" bolt makes a good mount.I settled on a spot right behind the front seats going across the vehicle. The folding back seat covers most of it to keep the honest people honest. The dishonest ones will see a padlock, but let's be honest ourselves... if someone wants it bad enough - they are going to get it anyway. I found a small ledge on both sides of the vehicle that is just forward of the rear wheelwells. I took a trip to the local hardware store where I put together a mounting kit that was simple and easy to install. For each mounting point, I used a 2.5" (long), .5" bolt (I used a hex-head), 2 flat washers, a lock washer, a regular nut and a large wingnut.
A view from back near the rear bumper facing the front of the wheelwell.A closer look at the wheelwell side of the bolt.I measured for two points 44.5" apart. This will put the bolts through the end-most holes on the jacks main rail. Stay .25" away from the wheelwell when measuring so the lower washer will fit nice and flat, and drill straight down through both layers of metal. You will need help from a friend to put the bolts in, one person stays outside, and one inside to drop on the first flat washer, lock washer, thread the nut and tighten it all down. I also used some black RTV on the bolt before putting it in. Since it is going up through the wheelwell, waterproofing should be considered a necessity. Drop the second flat washer on the bolt as a base for the Hi-Lift and then drill the second mounting hole.
The left side mounted with a wingnut.The right mounted with a wingnut.Once the bolts have been tightened down, all that is left is to drop the Hi-Lift in place and secure with the wingnuts. I used an extra set of bolts and wingnuts to secure the base to the jack. This makes for a nice 1-piece package when you need it.

Mounted Hi-Lift

These jacks are a must for anyone who ventures off the beaten path.

08/11/10 14:46

[tech/footer.htm]